|
Home > Archive > Home Repair forum > April 2006 > How to hang towel rod
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
How to hang towel rod
|
|
| hillacc@yahoo.com 2006-04-20, 11:21 am |
| A towel rod pulled loose in my bathroom -- predictably, since whoever
installed it just used screws into drywall. However, in trying to
rehang it, I learned that there is not enough room between the drywall
and whatever's behind it to get a toggle bolt in (can't drive the bolt
through far enough for the toggle to open). I've tried every size and
type of toggle bolt, molly bolt, etc., the hardware store has to offer
-- none will fit far enough into the hole for the
toggles/flanges/whatever to open. Whatever is behind the drywall is
HARD (like concrete hard).
For the time being, I've rigged it up by spackling one of those ribbed
plastic plugs into place (and I had to cut that off -- I would estimate
there is no more than 1/4 to 1/2 inch of room behind the drywall) to
put the screw into, but after a few months, that has become loose
(spackle is giving way). What is the right way for me to fasten this
towel rod to the wall?
Thanks in advance,
Jo Ann
| |
|
|
| borne@hboi.edu 2006-04-20, 11:21 am |
| Is this on an outside wall? If so, is it block or brick? If that is
the case, you will have to either bore into the block or brick and use
a concrete anchor. Or see if the rack can be moved, such that you can
screw right into the 1x4s that are probably attached to the block.
An easier solution is to cut a slit vertically or horizonally to allow
the open molly to go behind the drywall, and then rotate 90 degrees.
If this in an inside wall, be careful since you may have run into a
water pipe or such.
| |
| Goedjn 2006-04-20, 1:21 pm |
| On 20 Apr 2006 06:44:22 -0700, "hillacc@yahoo.com" <jah213@gmail.com>
wrote:
>A towel rod pulled loose in my bathroom -- predictably, since whoever
>installed it just used screws into drywall. However, in trying to
>rehang it, I learned that there is not enough room between the drywall
>and whatever's behind it to get a toggle bolt in (can't drive the bolt
>through far enough for the toggle to open). I've tried every size and
>type of toggle bolt, molly bolt, etc., the hardware store has to offer
>-- none will fit far enough into the hole for the
>toggles/flanges/whatever to open. Whatever is behind the drywall is
>HARD (like concrete hard).
>
>For the time being, I've rigged it up by spackling one of those ribbed
>plastic plugs into place (and I had to cut that off -- I would estimate
>there is no more than 1/4 to 1/2 inch of room behind the drywall) to
>put the screw into, but after a few months, that has become loose
>(spackle is giving way). What is the right way for me to fasten this
>towel rod to the wall?
>
>Thanks in advance,
>Jo Ann
Mounting board attached to the furring strips that are almost
certainly under the drywall, and then attach the towel rod to
the mounting board.
| |
| Edwin Pawlowski 2006-04-20, 3:21 pm |
|
"Goedjn" <prose@mail.uri.edu> wrote in message
> Mounting board attached to the furring strips that are almost
> certainly under the drywall, and then attach the towel rod to
> the mounting board.
That is probably the easiest and can be made decorative. Next would be to
find out what is behind the drywall and anchor into that material.
| |
| hillacc@yahoo.com 2006-04-20, 3:21 pm |
| Good suggestions, thanks! It's an outside wall and the house is wood
frame. Whatever is behind there is rock hard, though. The house is
+100 years old so could be something from an old repair or "whatever."
Going behind the drywall to figure out what's there is probably more
work than I'm ready to go to just to fix a towel bar.
I tried every kind of fastener shown on that web site and kept running
into the "no room behind the wall" problem. Cutting a slit may work
(I'm better than halfway there now, with the size of hole that has been
created putting in and taking out various anchors), and I like the
mounting board idea a lot, too.
Thanks again for the help!
Jo Ann
| |
|
| hillacc@yahoo.com wrote:
> Good suggestions, thanks! It's an outside wall and the house is wood
> frame. Whatever is behind there is rock hard, though. The house is
> +100 years old so could be something from an old repair or "whatever."
> Going behind the drywall to figure out what's there is probably more
> work than I'm ready to go to just to fix a towel bar.
>
> I tried every kind of fastener shown on that web site and kept running
> into the "no room behind the wall" problem. Cutting a slit may work
> (I'm better than halfway there now, with the size of hole that has been
> created putting in and taking out various anchors), and I like the
> mounting board idea a lot, too.
>
> Thanks again for the help!
>
> Jo Ann
>
I would consider tapcon screws. Drill deep enough into the hard stuff
and use a long screw that can bridge the gap behind the drywall. Will
look a bit ugly though. I do like the decorative board idea a lot too.
Inviato da X-Privat.Org - Registrazione gratuita http://www.x-privat.org/join.php
| |
| Norminn 2006-04-20, 4:21 pm |
| hillacc@yahoo.com wrote:
> Good suggestions, thanks! It's an outside wall and the house is wood
> frame. Whatever is behind there is rock hard, though. The house is
> +100 years old so could be something from an old repair or "whatever."
> Going behind the drywall to figure out what's there is probably more
> work than I'm ready to go to just to fix a towel bar.
>
> I tried every kind of fastener shown on that web site and kept running
> into the "no room behind the wall" problem. Cutting a slit may work
> (I'm better than halfway there now, with the size of hole that has been
> created putting in and taking out various anchors), and I like the
> mounting board idea a lot, too.
>
> Thanks again for the help!
>
> Jo Ann
>
Our condo only has 1x studs on outside walls. Since we have no children
to hang onto the towel rods, they stay up with plastic anchors. If your
latest installation doesn't last, you might want to try a lead anchor
deeper in the outside wall if it is brick. When the children were of an
age to chin themselves on towel rods, or whatever it was they did, I
nailed a board into the studs and anchored the rods to the board.
Didn't know then what I know now :o)
|
|
|
|
|