| Author |
What size drill bit for 1/4" mounting screw?
|
|
| Mary Weatherford 2006-05-28, 11:21 pm |
| I am installing an under the counter Sony radio/CD player in my kitchen. The
instructions call for 9/32" drill bit. The mounting screws are about 1/4" in
diameter - not larger. Do I need to buy a 9/32" drill bit or can I use the
1/4" drill bit in my set?
I am concerned that the holes will be too large and not hold the radio
securely.
Thank you for anyone who can answer this probably simple question.
Mary
| |
|
| Mary, 1/4" is equal to 8/32" which is 1/32 smaller than they recommend. If
the screw fits through the hole, it's fine
"Mary Weatherford" <m-weatherford@worldnet.att.net> wrote in message
news:C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net...
>I am installing an under the counter Sony radio/CD player in my kitchen.
>The instructions call for 9/32" drill bit. The mounting screws are about
>1/4" in diameter - not larger. Do I need to buy a 9/32" drill bit or can I
>use the 1/4" drill bit in my set?
> I am concerned that the holes will be too large and not hold the radio
> securely.
>
> Thank you for anyone who can answer this probably simple question.
>
> Mary
>
| |
| Tony Hwang 2006-05-28, 11:21 pm |
| Mary Weatherford wrote:
> I am installing an under the counter Sony radio/CD player in my kitchen. The
> instructions call for 9/32" drill bit. The mounting screws are about 1/4" in
> diameter - not larger. Do I need to buy a 9/32" drill bit or can I use the
> 1/4" drill bit in my set?
> I am concerned that the holes will be too large and not hold the radio
> securely.
>
> Thank you for anyone who can answer this probably simple question.
>
> Mary
>
>
Hi,
Your simple question calls for common sense answer, LOL.
What is the cabinet material? Wood? Melamine? MDF?
I'd just use pick or real small bit to make a pilot hole and drive the
screw in. Vari speed power screw driver is handy on a job like this.
| |
| Tony Hwang 2006-05-28, 11:21 pm |
| RBM wrote:
> Mary, 1/4" is equal to 8/32" which is 1/32 smaller than they recommend. If
> the screw fits through the hole, it's fine
>
>
>
> "Mary Weatherford" <m-weatherford@worldnet.att.net> wrote in message
> news:C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net...
>
>
>
>
That was a common sense answer to simple question, LOL
| |
| Mary Weatherford 2006-05-28, 11:21 pm |
| I am trying to save myself a trip to the hardware store and spending $8+ for
a bit I will use one time. Plus I only paid $45 for the radio. Also, since I
work and have no car it is a PITA to go to a hardware store.
The 1/4" drill bit I have is larger than the shank of the mounting screw.
Thanks,
Mary
PS I am a math statistics major but they never taught us anything about home
repair.
"RBM" <rbm2(remove this)@optonline.net> wrote in message
news:O8seg.860$T%1.334@fe10.lga...
> Mary, 1/4" is equal to 8/32" which is 1/32 smaller than they recommend. If
> the screw fits through the hole, it's fine
>
>
>
> "Mary Weatherford" <m-weatherford@worldnet.att.net> wrote in message
> news:C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net...
>
>
| |
| Charles Bishop 2006-05-28, 11:21 pm |
| In article <C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net>,
"Mary Weatherford" <m-weatherford@worldnet.att.net> wrote:
>I am installing an under the counter Sony radio/CD player in my kitchen. The
>instructions call for 9/32" drill bit. The mounting screws are about 1/4" in
>diameter - not larger. Do I need to buy a 9/32" drill bit or can I use the
>1/4" drill bit in my set?
>I am concerned that the holes will be too large and not hold the radio
>securely.
>
>Thank you for anyone who can answer this probably simple question.
Is the hole just for the screws to pass through? If so the 1/4" will be
fine. If the screws don't fit easily, you can use the 1/4" bit again and
"wiggle" it a bit while drilling and this will enlarge the hole.
--
charles
| |
| patrick mitchel 2006-05-29, 5:21 am |
|
Mary Weatherford <m-weatherford@worldnet.att.net> wrote in message
news:C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net...
> I am installing an under the counter Sony radio/CD player in my kitchen.
The
> instructions call for 9/32" drill bit. The mounting screws are about 1/4"
in
> diameter - not larger. Do I need to buy a 9/32" drill bit or can I use the
> 1/4" drill bit in my set?
> I am concerned that the holes will be too large and not hold the radio
> securely.
>
> Thank you for anyone who can answer this probably simple question.
>
> Mary
Find a waste piece of the material similar to the material you're going to
be mounting the radio to, try to drill though that and drive the screw. If
you have good bite, you're home. Pat
| |
| Charles Bishop 2006-05-29, 12:21 pm |
| In article <4dvma5F1ce02uU1@individual.net>, "patrick mitchel"
<patm317@hotmail.com> wrote:
>Mary Weatherford <m-weatherford@worldnet.att.net> wrote in message
>news:C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net...
>The
>in
> Find a waste piece of the material similar to the material you're going to
>be mounting the radio to, try to drill though that and drive the screw. If
>you have good bite, you're home.
I think maybe the screw is intended to go through the hole and be held by
a nut - I don't think it's a wood screw but a bolt. In which case the 1/4"
bit will work fine, just wiggle it a bit to enlarge the hole slightly if
needed.
Mary, did you do it yet? How did it turn out?
--
charles
| |
| Mary Weatherford 2006-05-29, 6:21 pm |
| Thank you all for your input. The radio will be mounted on the underside of
a kitchen cabinet. I think the cabinet bottom is a material similar to
masonite. This is rental unit so I don't have any information about the
construction of the cupboards. I do not have any scraps to test the drill
bit. The cabinet is too small to get the drill inside so I will have to go
at it from the underside. I have a template from Sony for drilling the
holes. I have back problems and drilling at that angle is highly unlikely
for me. I will need help with this so I don't have an update on my progress.
Sony only described the screws as mounting screws. They look like a kind of
machine screw with slightly rounded Philips heads. The screws fit into
adjustable spacers to enable the radio to fit under any cabinet. The screws
go in to the radio to hold it in place.
Mary
"patrick mitchel" <patm317@hotmail.com> wrote in message
news:4dvma5F1ce02uU1@individual.net...
>
> Mary Weatherford <m-weatherford@worldnet.att.net> wrote in message
> news:C3seg.108967$Fs1.24737@bgtnsc05-news.ops.worldnet.att.net...
> The
> in
> Find a waste piece of the material similar to the material you're going to
> be mounting the radio to, try to drill though that and drive the screw. If
> you have good bite, you're home. Pat
>
>
| |
| Rod & Betty Jo 2006-06-01, 3:21 pm |
|
"Mary Weatherford" <m-weatherford@worldnet.att.net> wrote in message
news:yrseg.109026$Fs1.43206@bgtnsc05-news.ops.worldnet.att.net...
>I am trying to save myself a trip to the hardware store and spending $8+
>for a bit I will use one time. Plus I only paid $45 for the radio. Also,
>since I work and have no car it is a PITA to go to a hardware store.
>
> The 1/4" drill bit I have is larger than the shank of the mounting screw.
>
> Thanks,
> Mary
> PS I am a math statistics major but they never taught us anything about
> home repair.
Use a finishing nail (small head) as your "drill bit"(works surprisingly
well)......Or if your cabinet underside is plywood/wood instead of particle
board you can probably use your drill to drive the screws without a pilot
hole......Rod
| |
|
|
Mary Weatherford wrote:
> Thank you all for your input. The radio will be mounted on the underside of
> a kitchen cabinet. I think the cabinet bottom is a material similar to
> masonite. This is rental unit so I don't have any information about the
> construction of the cupboards. I do not have any scraps to test the drill
> bit. The cabinet is too small to get the drill inside so I will have to go
> at it from the underside. I have a template from Sony for drilling the
> holes. I have back problems and drilling at that angle is highly unlikely
> for me. I will need help with this so I don't have an update on my progress.
> Sony only described the screws as mounting screws. They look like a kind of
> machine screw with slightly rounded Philips heads. The screws fit into
> adjustable spacers to enable the radio to fit under any cabinet. The screws
> go in to the radio to hold it in place.
>
> Mary
Yeah, I got one of those radios, they are great. Is this the kind with
the Cd and weather and tv and remote? Anyway, since it's a machine
screw and the screw fits through a 1/4 hole, you're home free.
[color=darkred]
> "patrick mitchel" <patm317@hotmail.com> wrote in message
> news:4dvma5F1ce02uU1@individual.net...
|
|
|
|