|
Home > Archive > Home Repair forum > February 2008 > Air brad nailer - instructions?
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
Air brad nailer - instructions?
|
|
|
| A while ago I picked up a cheap, no-name pneumatic brad nailer. The
instructions that came with it are pretty much useless. It's worked well the
few times I've used it.
I'm going to be installing some molding with this gun and don't want to
split or drive through the material, so I'm trying to locate some
instructions on how best to use this gun.
It will drive 18 gauge nails or staples, 3/4" to 2" (?) in length. On the
back of the head there appears to be an adjustment knob that turns easily
about 90 degrees, but doesn't appear to do anything.
So, I'd like to know...
- What is the optimum air pressure to supply the nailer with?
- Should that top actually adjust anything?
- Any links on how to use a brad nailer properly?
| |
| Robert Allison 2008-02-05, 5:25 pm |
| Calab wrote:
> A while ago I picked up a cheap, no-name pneumatic brad nailer. The
> instructions that came with it are pretty much useless. It's worked well the
> few times I've used it.
>
> I'm going to be installing some molding with this gun and don't want to
> split or drive through the material, so I'm trying to locate some
> instructions on how best to use this gun.
>
> It will drive 18 gauge nails or staples, 3/4" to 2" (?) in length. On the
> back of the head there appears to be an adjustment knob that turns easily
> about 90 degrees, but doesn't appear to do anything.
>
> So, I'd like to know...
>
> - What is the optimum air pressure to supply the nailer with?
Probably 90-100 PSI.
> - Should that top actually adjust anything?
It is most likely an adjustable vent. When you fire the gun, does air
come out of it? If so, then it is adjustable so that you can turn it
away from you when using it at different angles.
> - Any links on how to use a brad nailer properly?
Press it to the wood and fire. Hold it against the wood firmly and
learn exactly where the brad comes out so that you can center the nail
where you want it to go.
Don't shoot yourself.
Don't shoot anyone else.
Don't shoot pets or other animals, unless they are attacking you.
Check often to make sure you still have brads in the gun. It is a pain
to find out that that piece of trim was nailed with nothing but air.
Oil the gun daily (a few drops in the air inlet).
Keep it clean and clean it regularly.
--
Robert Allison
Rimshot, Inc.
Georgetown, TX
| |
| HeyBub 2008-02-06, 3:25 am |
| Calab wrote:
>
> - What is the optimum air pressure to supply the nailer with?
Probably 80-100 pounds. Air pressure may be the only way of adjusting the
depth of the nail. At the least, the air pressure will be a rough guide.
There may be a fine adjustment on the gun.
> - Should that top actually adjust anything?
Nah, it's for the exhaust.
> - Any links on how to use a brad nailer properly?
Aside from other tips, practice with scraps of the stuff you're going to
nail and the actual surface into which you intend to nail it. For example,
nailing a bit of moulding into wood will differ from nailing that same bit
of moulding into 1/2" of sheetrock before the nail hits wood.
| |
| JohnnyC 2008-02-06, 9:26 am |
| Wear eye protection!!!
Make sure the gun is not in bump fire mode, meaning you have to pull the
trigger to fire the nail.
Practice with scraps of wood.
Do not adjust the nail depth with the gun attached to the air hose.
Have a nail set handy
Unplug your compressor and release the air from tank after using it.
A few drops of oil in the gun air hole before use.
"Calab" <myspam@csd.ca> wrote in message
news:vS0qj.45298$4w.22945@pd7urf2no...
>A while ago I picked up a cheap, no-name pneumatic brad nailer. The
>instructions that came with it are pretty much useless. It's worked well
>the few times I've used it.
>
> I'm going to be installing some molding with this gun and don't want to
> split or drive through the material, so I'm trying to locate some
> instructions on how best to use this gun.
>
> It will drive 18 gauge nails or staples, 3/4" to 2" (?) in length. On the
> back of the head there appears to be an adjustment knob that turns easily
> about 90 degrees, but doesn't appear to do anything.
>
> So, I'd like to know...
>
> - What is the optimum air pressure to supply the nailer with?
> - Should that top actually adjust anything?
> - Any links on how to use a brad nailer properly?
>
>
|
|
|
|
|